here is a list of all channels of the psl subsystem. We changed the generic channel names to final names now.
Refcav channels are now C3:PSL-RCAV and analyzer cavity channels are C3:PSL-ACAV. Rest see below...
#####################
# 10W MOPA channels #
#####################
[C3:PSL-126MOPA_AMPMON] # internal laser power monitor
[C3:PSL-126MOPA_126MON] # internal NPRO power monitor
[C3:PSL-126MOPA_DS1] # diode sensor 1
[C3:PSL-126MOPA_DS2] # diode sensor 2
[C3:PSL-126MOPA_DS3] # diode sensor 3
[C3:PSL-126MOPA_DS4] # diode sensor 4
[C3:PSL-126MOPA_DS5] # diode sensor 5
[C3:PSL-126MOPA_DS6] # diode sensor 6
[C3:PSL-126MOPA_DS7] # diode sensor 7
[C3:PSL-126MOPA_DS8] # diode sensor 8
[C3:PSL-126MOPA_126PWR] # NPRO power monitor
[C3:PSL-126MOPA_DTMP] # diode temperature
[C3:PSL-126MOPA_LTMP] # pump diode temperature
[C3:PSL-126MOPA_DMON] # diode output monitor
[C3:PSL-126MOPA_LMON] # pump diode output monitor
[C3:PSL-126MOPA_CURMON] # pump diode current monitor
[C3:PSL-126MOPA_DTEC] # diode heater voltage
[C3:PSL-126MOPA_LTEC] # pump diode heater voltage
[C3:PSL-126MOPA_CURMON2] # pump diode current monitor
[C3:PSL-126MOPA_HTEMP] # head temperature
[C3:PSL-126MOPA_HTEMPSET] # head temperature set point
[C3:PSL-126MOPA_FAULT] # laser fault indicator
[C3:PSL-126MOPA_INTERLOCK] # interlock control
[C3:PSL-126MOPA_SHUTTER] # shutter control
[C3:PSL-126MOPA_126LASE] # NPRO lase status
[C3:PSL-126MOPA_AMPON] # power amplifier lase status
[C3:PSL-126MOPA_SHUTOPENEX] #
[C3:PSL-126MOPA_STANDBY] #
[C3:PSL-126MOPA_126NE] # NPRO noise eater
[C3:PSL-126MOPA_126STANDBY] # NPRO standby
[C3:PSL-126MOPA_DCAMP] #
[C3:PSL-126MOPA_126CURADJ] #
[C3:PSL-126MOPA_126SLOW] #
[C3:PSL-126MOPA_BEAMON] # beam on logical
#######################
# 80 MHz VCO channels #
#######################
[C3:PSL-FSS_VCODETPWR] # 80 MHz VCO PWR
[C3:PSL-FSS_VCOTESTSW] # enable/disable test input
[C3:PSL-FSS_VCOWIDESW] # enable/disable wideband input
######################
# other FSS channels #
######################
[C3:PSL-FSS_SW1] # frequency servo front panel switch
[C3:PSL-FSS_SW2] # frequency servo front panel switch
[C3:PSL-FSS_INOFFSET] # 21.5 MHz mixer input offset adjust
[C3:PSL-FSS_MGAIN] # frequency servo common gain
[C3:PSL-FSS_FASTGAIN] # phase correcting EOM gain
[C3:PSL-FSS_PHCON] # 21.5 MHz phase control
[C3:PSL-FSS_RFADJ] # 21.5 MHz oscillator output
[C3:PSL-FSS_SLOWDC] # slow actuator voltage
[C3:PSL-FSS_MODET] #
[C3:PSL-FSS_PHFLIP] # 21.5 MHz 180 degree phase flip
[C3:PSL-FSS_MIXERM] # 21.5 MHz mixer monitor
[C3:PSL-FSS_SLOWM] # slow actuator voltage monitor
[C3:PSL-FSS_TIDALINPUT] #
[C3:PSL-FSS_RFPDDC] # 21.5 MHz photodetector DC output
[C3:PSL-FSS_LODET] # detected 21.5 MHz output
[C3:PSL-FSS_PCDET] #
[C3:PSL-FSS_FAST] # fast actuator voltage
[C3:PSL-FSS_PCDRIVE] # drive to the phase correcting EOM
[C3:PSL-FSS_RCTRANSPD] # reference cavity transmission
[C3:PSL-FSS_RMTEMP] # room temperature
[C3:PSL-FSS_RCTEMP] # reference cavity temperature
[C3:PSL-FSS_HEATER] # reference cavity heater power
[C3:PSL-FSS_TIDALOUT] #
[C3:PSL-FSS_RCTLL] # reference cavity transmitted light level
[C3:PSL-FSS_RAMP] # slow actuator ramp, used in lock acquisition
################
# PMC channels #
################
[C3:PSL-PMC_SW1] # PMC servo front panel switch
[C3:PSL-PMC_SW2] # PMC servo front panel switch
[C3:PSL-PMC_MODET]
[C3:PSL-PMC_PHFLIP] # 35.5 MHz 180 degree phase flip
[C3:PSL-PMC_PHCON] # 35.5 MHz phase control
[C3:PSL-PMC_RFADJ] # 35.5 MHz oscillator output
[C3:PSL-PMC_PMCERR] # PMC error point
[C3:PSL-PMC_RFPDDC] # 35.5 MHz photodetector DC output
[C3:PSL-PMC_LODET] # detected 35.5 MHz output
[C3:PSL-PMC_PMCTRANSPD] # PMC transmission
[C3:PSL-PMC_PCDRIVE] #
[C3:PSL-PMC_PZT] # PMC PZT voltage
[C3:PSL-PMC_INOFFSET] # 35.5 MHz mixer input offset adjust
[C3:PSL-PMC_GAIN] # PMC loop gain
[C3:PSL-PMC_RAMP] # PMC PZT ramp, used in lock acquisition
[C3:PSL-PMC_BLANK] # blanking input to the PMC PZT
[C3:PSL-PMC_PMCTLL] # PMC transmitted light level
################
# ISS channels #
################
[C3:PSL-ISS_SW1] # intensity servo front panel switch
[C3:PSL-ISS_SW2] # intensity servo front panel switch
[C3:PSL-ISS_AOMRF] # rf drive for intensity stabilization
[C3:PSL-ISS_ISERR] # intensity servo error point
[C3:PSL-ISS_GAIN] # intensity servo gain
[C3:PSL-ISS_ISET] # intensity servo set point
#############################
# 16bit D/A channels - ACAV #
# 4116-card #
#############################
[C3:PSL-ACAV_HEATER] # analyzer cavity heater power
[C3:PSL-ACAV_SLOWDC] # feedback to tidal input of other cavity
#############################
# 16bit A/D channels - ACAV #
# 3123-card #
#############################
[C3:PSL-ACAV_RCTEMP] # reference cavity temperature
[C3:PSL-ACAV_RMTEMP] # room temperature
[C3:PSL-ACAV_RCTRANSPD] # analyzer cavity transmission
[C3:PSL-ACAV_RFPDDC] # RF photodetector DC output
[C3:PSL-ACAV_PDHOUT] # PDH servo output signal
#############################
# software channels - ACAV #
#############################
[C3:PSL-ACAV_KP] # pid loop p-gain
[C3:PSL-ACAV_KI] # pid loop i-gain
[C3:PSL-ACAV_KD] # pid loop d-gain
[C3:PSL-ACAV_LOCKEDLEVEL] # threshold level below which pid does nothing
[C3:PSL-ACAV_TIMEOUT] # pid loop sample time
[C3:PSL-ACAV_VERSION] # pid loop software version
[C3:PSL-ACAV_DEBUG] # pid loop debug messages on/off
[C3:PSL-ACAV_ENABLE] # pid loop on/off
[C3:PSL-ACAV_SETPT] # temperature setpoint
[C3:PSL-ACAV_SCALE] # scaling factor
##############################
# software channels - REFCAV #
##############################
[C3:PSL-RCAV_KP] # pid loop p-gain
[C3:PSL-RCAV_KI] # pid loop i-gain
[C3:PSL-RCAV_KD] # pid loop d-gain
[C3:PSL-RCAV_LOCKEDLEVEL] # threshold level below which pid does nothing
[C3:PSL-RCAV_TIMEOUT] # pid loop sample time
[C3:PSL-RCAV_VERSION] # pid loop software version
[C3:PSL-RCAV_DEBUG] # pid loop debug messages on/off
[C3:PSL-RCAV_ENABLE] # pid loop on/off
[C3:PSL-RCAV_SETPT] # temperature setpoint
[C3:PSL-RCAV_SCALE] # scaling factor
##############################
# software channels - TIDAL #
##############################
[C3:PSL-TIDAL_KP] # pid loop p-gain
[C3:PSL-TIDAL_KI] # pid loop i-gain
[C3:PSL-TIDAL_KD] # pid loop d-gain
[C3:PSL-TIDAL_LOCKEDLEVEL] # threshold level below which pid does nothing
[C3:PSL-TIDAL_TIMEOUT] # pid loop sample time
[C3:PSL-TIDAL_VERSION] # pid loop software version
[C3:PSL-TIDAL_DEBUG] # pid loop debug messages on/off
[C3:PSL-TIDAL_ENABLE] # pid loop on/off
[C3:PSL-TIDAL_SETPT] # temperature setpoint
[C3:PSL-TIDAL_SCALE] # scaling factor
|