Facility

• Work
  • Replacing wooden work benches
    • W60" x H28-34" x D30" http://www.globalindustrial.com/p/work-benches/systems/adjustable-height/60x30-esd-square-edge-power-apron-production-bench-blue
    • W72" x H28-34" x D30" http://www.globalindustrial.com/p/work-benches/systems/adjustable-height/72x30-esd-square-edge-power-apron-production-bench-blue
    • Lower shelf W60" http://www.globalindustrial.com/p/work-benches/systems/adjustable-height/60-w-lower-shelf-bench-15-d-blue 
    • Lower shelf W72" http://www.globalindustrial.com/p/work-benches/systems/adjustable-height/72-w-lower-shelf-bench-15-d-blue
  • Replacing a cabinet at the south wall by a lockable cabinet
    • W36" x H72" x D20"
  • Cleaning of the floor
  • Plug a big hole on the wall (Done)
  • Plug slits on the roof of the HEPA booth - "There should be the blanking panels there."
     
  • Install laser Safety curtain (Peter is working on this)
     
  • Place a sticky mat
  • Prepare clean supplies (Shoes/Coverall/Hats/Gloves) => go to VWR stock room
  • Prepare Al foils (All foils inc, should get a certificate everytime to ensure UHV compatibility)
  • Plastic boxes for storage http://www.drillspot.com/products/422140/Rubbermaid_2282-00-CLR_18GAL_Clear_Snap_Case
    (Steve is helping Koji to get them)
     
• Design
  • Optical layout
     
• Test
  • Confirm particle level
     
• Note: Optical Table W96" x D48" x H27"

Mechanics

• Work 
  •  
• Design
  • How do we hold the PDs, QPDs, and black glass - we put 2 PDs and 2 QPDs on the PD mounting blacket.
  •  
•  
• Test
   
• Things to be tested
  • New suspension scheme (cup & cone design)
  • Balancing the plates
  • Dummy metal payload?
• => Suspending test with a suspension cage for a Faraday isolator@CIT
  • Supporting block for the suspension cage (to mimic the OMC suspension)
• Things to be designed
  • Wire end (cone)
  • Diode holding structures
    PD/QPD/PZT holding structure
• PZT alignment
• Prototyping with metal parts?
• UV glue? (heat) / gluing test
• Balance / ballast
   
• Solid works

Optics

• Mirrors to be delivered ~Aug
• Design down select
  • Between "Single output & BS" vs "Two outputs & no BS"
• Mode design
• Finalization of scattering paths / PD angles etc
   
• Things to be decided / confirmed:
  • How to handle optics / assemblies (Talk to the prev people)
  • First contact? (Margot: applicable to a short Rc of ~2.5m)
  • Gluing templates to be designed (how to handle it?)
• Things to be tested:
  • R&T of each mirror
  • Cavity ref/trans/finesse
  • PD QE / incident angle
     
• What PD do we use?
   
• CCD beam analyzer (Zach: It is fixed.)
   
• PD angle measurement
• Obtain EG&G 3mm PDs

Electronics

• Electronics / CDS electronics / software
   
• Things to be tested
  • QPD/PD pre-selections (QE/noise)
  • Functionality test of QPD/PD/PZT

Shipping, storage etc

• Shipping cage drawing
  https://dcc.ligo.org/cgi-bin/private/DocDB/ShowDocument?docid=70209

Jun/July
    - Lab renovtion
    - Mechanics design
    - Glue training
Aug
    - Mirror delivery
    - Basic optics test
Sept
    - Cavity test
    - Suspending test
NOV~DEC
    - Shipping to LLO

Open questions
    Two optical designs
    Procedure
    Modeling
    Clamp design / stencil design
    gluing-installation procedure

LIGO Document G1200683-v1:
aLIGO OMC fabrication and testing plan

aLIGO OMC wiki