40m QIL Cryo_Lab CTN SUS_Lab CAML OMC_Lab CRIME_Lab FEA ENG_Labs OptContFac Mariner WBEEShop
  40m Log, Page 72 of 350  Not logged in ELOG logo
ID Date Author Type Category Subject Text Attachments
  14019   Tue Jun 26 16:28:00 2018 gautamUpdateSUSCoil driver protoboard characterizationI wanted to investigate my coil driver
noise measurement technique under more controlled
circumstances, so I spent yesterday setting
 IMG_7060.JPGETMXstitchced.pdfETMXfullSpan.pdfPSRR.pdf 
  14018   Tue Jun 26 10:50:14 2018 poojaUpdateCamerasBeam spot tracking using OpenCVAim: To track the motion of beam spot in
simulated video.

I simulated a video that moves
 cv2_track_fig.pdf 
  14017   Tue Jun 26 10:06:39 2018 keerthanaUpdateAUXFirst Coherent AUX Scan of PRC Using AM Sidebands(Jon, Keerthana, Sandrine)

I am attaching the plots of the
Reflected and transmitted AUX beam. In the
 TRANS.pdfREFL.pdf 
  14016   Mon Jun 25 22:27:57 2018 shrutiUpdatePEMSeismometer temp control - heater circuitAfter removing all the clamping screws
from the heater circuit board, I soldered
the wire connecting IRF630 to the output
  
  14015   Mon Jun 25 21:14:08 2018 KojiSummaryGeneralRe: A summary of the Tip-TIlt Mirror Holder design changes3.
- Do we need this much of extended
range of the clamp location? How much range
  
  14014   Mon Jun 25 19:14:02 2018 UditSummaryGeneralRe: A summary of the Tip-TIlt Mirror Holder design changes2. Weighted screw rod at the bottom
for tilting the mirror-holder:

The screw length selected here
 4-1.png4-2.png 
  14013   Sun Jun 24 23:13:46 2018 johannesUpdateGeneralAUX beam alignment issuesAt some point we want to change the AUX
injection on the AS table to interfere less
with the normal interferometer path, and
 AS_AUX_SETUP.pdf 
  14012   Sun Jun 24 20:02:07 2018 gautamUpdateSUSSome notes about coil driver noiseSummary:

For a series resistance of 4.5
kohm, we are suffering from the noise-gain
 CoilDriverSchematic.pdfD010001_2k_fastOnly_2.25k.pdfD010001_4k_fastOnly_4.5k.pdf 
  14011   Sat Jun 23 20:54:35 2018 KojiUpdateAUXFirst Coherent AUX Scan of PRC Using AM SidebandsHow much was the osc freq of the marconi?
And then how much was the resulting freq
offset between PSL and AUX?
  
  14010   Sat Jun 23 13:08:41 2018 JonUpdateAUXFirst Coherent AUX Scan of PRC Using AM Sidebands[Jon, Keerthana, Sandrine]

Thu.-Fri. we continued with PRC
scans using the AUX laser, but now the "scanned"
 IMG_2695.jpegIMG_2698.jpegIMG_2699.jpeg 
  14009   Fri Jun 22 18:30:21 2018 gautamUpdateSUSITMY_UL sensorI think if the magnet fell off, we would
see high DC signal, and not 0 as we do now.
I suspect satellite box or PD readout board/cabling.
  
  14008   Fri Jun 22 15:22:39 2018 sudoUpdateCDSDTT working


Quote:


  
  14007   Fri Jun 22 15:13:47 2018 gautamUpdateCDSDTT workingSeems like DTT also works now. The trick
seems to be to run 
 Screenshot_from_2018-06-22_15-12-37.png 
  14006   Fri Jun 22 14:18:04 2018 SteveUpdatePSLOptics on AS table 




  
  14005   Fri Jun 22 10:42:52 2018 poojaUpdate Developing neural networksAim: To find a model that trains the simulated
data of Gaussian beam spot moving in a vertical
direction by the application of a sinusoidal
 NN_fig.zip 
  14004   Fri Jun 22 08:50:33 2018 SteveUpdateSUSITMY_UL sensorWe may lost the UL magnet or LED  ITMY_UL.png 
  14003   Fri Jun 22 00:59:43 2018 gautamUpdateCDSpianosa functional, but NO DTTMEDM, EPICS and dataviewer seem to work,
but diaggui still doesn't work (it doesn't
work on Rossa either, same problem as reported
  
  14002   Fri Jun 22 00:06:13 2018 shrutiUpdateGeneralover-head fluorescent lights downTwo out of the four over-head fluorescent
lights in the X end of the interferometer
were flickering today.
  
  14001   Thu Jun 21 23:59:12 2018 shrutiUpdatePEMSeismometer temp controlWe (Rana and I) are re-assembling the temperature
controls on the seismometer to attempt PID
control and then improve it using reinforcement
  
  14000   Thu Jun 21 22:13:12 2018 gautamUpdateCDSpianosa upgradepianosa   
  13999   Thu Jun 21 18:25:57 2018 gautamUpdateSUSETMX coil driver re-installedInitial tests look promising. Local damping
works and I
even locked the X arm using POX,
  
  13998   Thu Jun 21 15:32:05 2018 gautamUpdateElectronicsEX AA filter range change[steve, gautam]

I took this opportunity of EX downtime
to change the supply voltage for the AA unit
  
  13997   Thu Jun 21 14:57:59 2018 KojiSummaryGeneralA summary of the Tip-TIlt Mirror Holder design changes> 2. Weighted screw rod at the
bottom for tilting the mirror-holder:

Too long. The design of the holder
  
  13996   Thu Jun 21 14:23:22 2018 Udit KhandelwalSummaryGeneralA summary of the Tip-TIlt Mirror Holder design changesHere’s a quick summary of the Tip-Tilt
Design updates (all files are in the dropbox
in [TipTiltSus>TT_New]) that I have been
 1.png2.png3-1.png3-2.png3-3.png 
  13995   Thu Jun 21 13:24:00 2018 keerthanaUpdateelogThe cavity scan data of June 20(Jon, Keerthana, Sandrine)

We tried to align the AUX and PSL
laser yesterday. We collected the data from
 AS110_Beat.pdfYEND_Beat.pdf 
  13994   Thu Jun 21 09:33:02 2018 JonUpdate AUX Mode Scans of YARM, PRC cavities[Jon, Keerthana, Sandrina]

Yesterday we carried out preliminary
proof-of-concept measurements using
 YARM_AUX_RF-offset_scan.pdftemp_broadband_refl33.pdf 
  13993   Thu Jun 21 03:13:37 2018 gautamUpdateSUSETMX coil driver noiseI decided to take a quick look at the data.
Changes made to the ETMX coil driver board:


Fast path series resistances:
 ETMXsticthced.pdfETMXFullSpan.pdfETMXCoilDriver.fil.zip 
  13992   Thu Jun 21 00:14:01 2018 gautamUpdateSUSETMX coil driver outI finished the re-soldering work today,
and have measured the coil driver noise pre-Mods
and post-Mods. Analysis tomorrow. I am holding
  
  13991   Wed Jun 20 20:39:36 2018 poojaUpdateCamerasCCD calibration using LED1050E 




  
  13990   Wed Jun 20 09:16:56 2018 SteveUpdatePEMdusty labYou should wipe off the table cover before
you take it off next time.

It is important to turn up the
 AP.JPGITMY.JPGITMX.JPGSP.JPG 
  13989   Wed Jun 20 00:57:04 2018 johannesUpdateGeneralAUX beam alignment issuesWe did swap a lens as discussed in elog 13968,
but they both had f=100mm specified, the
difference being one was AR-coated for 1064
 as110_rf_30MHz.pdfyend_rf_30MHz.pdf 
  13988   Tue Jun 19 23:27:27 2018 gautamUpdateSUSETMX coil driver work in AM tomorrowPer discussion today eve, barring objections,   
  13987   Tue Jun 19 18:56:55 2018 JonUpdateGeneralAUX beam alignment issuesNot much progress today with the AUX cavity
scans. I've determined there still are
some alignment issues.
  
  13986   Tue Jun 19 14:08:37 2018 poojaUpdateCamerasCCD calibration using LED1050EAim: To measure the optical power from
led using a powermeter.

Yesterday Gautam drilled a larger
  
  13985   Tue Jun 19 00:19:00 2018 gautamUpdateASCPOP status checkMotivation:


I want to use the QPD at
POP, calibrate it into physical units, and
  
  13984   Mon Jun 18 19:47:02 2018 gautamUpdateGeneralMICH actuator calibrationSummary:

The actuator (pendulum) gains for
the Beam Splitter and the two ITMs were measured
 AS55cal_process.pdfAS55cal.pdfMICH_act_calib.pdf 
  13983   Mon Jun 18 16:57:54 2018 KojiUpdatePSLOptics on AS tableOf course, many (but no all) of the optics
were custom-ordered back in ~2000.
  
  13982   Mon Jun 18 15:59:17 2018 johannesUpdatePSLOptics on AS table


Quote:


  
  13981   Mon Jun 18 14:32:42 2018 gautamUpdatePSLOptics on AS tableYesterday, I moved the following optics:


Lens in front of AS110
PD.
BS splitting light between
  
  13980   Mon Jun 18 12:07:03 2018 KojiUpdateGeneralChiara new USB 4TB DIskThe initial local backup with rsync was
done. Now
the new 4TB disk is (supposed to be) automatically
  
  13979   Mon Jun 18 11:12:23 2018 KiraSummaryPEMfinishing up work at the labSince I am finishing my job at the lab,
I have stored all my electronics in a box
(attachment 1) and placed it under the table
 IMG_20180618_101640.jpgIMG_20180618_093920.jpgIMG_20180618_093932.jpg 
  13978   Mon Jun 18 10:34:45 2018 johannesUpdateComputer Scripts / Programsrunning comsol job on optimusI'm running a comsol job on optimus
in a tmux session named cryocavs. Should
be done in less than 24 hours, judging by
  
  13977   Sun Jun 17 14:20:35 2018 KojiUpdateGeneralChiara new USB 4TB DIskI have connected a 4TB disk to chiara via
a USB-SATA adapter. This disk has been recognized
as /dev/sde. A GUID Partition Table (GPT),
  
  13976   Sat Jun 16 20:57:59 2018 JonUpdateGeneralPRC modescan attemptHere's a Finesse modeling of what
we're expecting to observe with this
test. It uses Gautam's base
 40M_SRMI_AM_annotated.pdf40M_DRMI_AM.pdf 
  13975   Sat Jun 16 01:25:29 2018 KojiUpdateGeneralPRC modescan attemptThe PRC FSR is, of course, very close to
twice of our f1 moudlation frequency (11MHz
x 2 = 22MHz) .
  
  13974   Sat Jun 16 00:26:48 2018 gautamUpdateGeneralPRC modescan attempt[Jon, Gautam, Johannes]

We did the following today:


Dither align arms such
  
  13973   Fri Jun 15 14:22:05 2018 gautamUpdateALSBeatMouth PDFR measurementI did the measurement with the BeatMouth
open today. Main changes:


Directly pipe the RF output
 BeatMouthPDFR.pdfBeatMouth_PDFRdata.tgz 
  13972   Fri Jun 15 09:51:55 2018 poojaUpdateCamerasDeveloping neural networkAim : To develop a neural network on simulated
data.

I developed a python code that
 nn_1.pdfnn_2.pdf 
  13971   Fri Jun 15 09:14:42 2018 SteveUpdateGeneralOplev sumsOplev sums of 240 days.




 opSums.png 
  13970   Fri Jun 15 08:09:15 2018 SteveBureaucracyGeneralcleaning up at the PSL enclousureThe cabeling was cleaned up a little bit
yesterday morning. The upper back side is
still massy.
 before.jpgafter.jpgback_side.jpg 
ELOG V3.1.3-