40m QIL Cryo_Lab CTN SUS_Lab TCS_Lab OMC_Lab CRIME_Lab FEA ENG_Labs OptContFac Mariner WBEEShop
  40m Log, Page 69 of 348  Not logged in ELOG logo
ID Date Author Type Category Subject Text Attachments
  14070   Fri Jul 13 23:23:49 2018 poojaUpdateCamerasUpdate in developing neural networksAim: To develop a neural
network that resolves mirror motion from
 nn_simulation_2_nodes4_lr0p00001_beta1_0p8_beta2_0p85.pdfnn_simulation_2_nodes8_lr0p00001_beta1_0p8_beta2_0p85.pdf 
  14069   Fri Jul 13 20:36:33 2018 KojiSummaryGeneralIn vac/In air heater wiring I went to the Y-end and took more photos
of the cable stand. These revealed that in-vac
pin #13 is connected to the shield of the
 heater_wiring.pdf 
  14068   Fri Jul 13 18:01:13 2018 gautamUpdateGeneralLow power MCAfter getting the go ahead from Steve,
I removed the physical beam block on the
PSL table, sent the beam into the IFO, and
  
  14067   Fri Jul 13 17:13:45 2018 KojiUpdateGeneralVent objectives and prepNotice:
I removed these 75Ohm video cables.
 P_20180713_020603.jpg 
  14066   Fri Jul 13 16:26:52 2018 SteveUpdateVACVent 80 is completing...Steve and Aaron,

6 hrs vent is reaching equlibrium
to room air. It took 3 and a half instrument
 @atm.pngvent80_7h.pngventregN2&Air_c.jpg 
  14064   Fri Jul 13 10:54:55 2018 aaronUpdateVACVent 80[aaron, steve]

Steve gave me a venting tutorial.
I'll record this in probably a bit more
 vent80wtiptilts.png 
  14063   Fri Jul 13 02:52:11 2018 gautamUpdateGeneralVent objectives and prep[KA,
GV]
 preVentStatus.png 
  14062   Fri Jul 13 00:15:13 2018 Annalisa, TerraConfigurationAUXY arm cavity scan [Annalisa, Terra, Koji, Gautam]

Summary: We
find a configuration for arm scans which
 IMG_6492.JPGIMG_6494.JPG 
  14061   Thu Jul 12 23:59:14 2018 gautamUpdateGeneralVent objectives and prepVent
objectives:
  
  14060   Thu Jul 12 21:16:25 2018 aaronUpdateOMCChecking OMC ElectronicsIn preparation for tomorrow's vent,
I'm checking some of the OMC-related
electronics we plan to use.
  
  14059   Thu Jul 12 16:18:22 2018 SteveUpdateVACVent preparationsWe are getting ready to vent.

 
 before_Vent.pngbefore_Vent_cond.png 
  14058   Thu Jul 12 15:15:47 2018 SandrineUpdate Beat Note Measurements for Cavity Scans(Gautam, Sandrine)

We calculated the expected power
of the beat note for Annalisa's Y arm
  
  14057   Thu Jul 12 14:06:39 2018 keerthanaUpdateelogFinesse and Analytical solution - ComparisonI tried to compare the cavity scan data
we get from the Finesse simulation and that
we expect from the Analytical solution. The
 finesse_cavity.pngAnalytical1.pdfFinesse_Analytical.pdfDifference.pdf 
  14056   Thu Jul 12 12:26:39 2018 aaronUpdateGeneralOMC revivalWe found a diagram describing the DC Readout
wiring
scheme on the wiki page for DC
  
  14055   Thu Jul 12 11:13:39 2018 gautamUpdateGeneralOMC revivalAaron and I are going to do the checkout
of the OMC electronics outside vacuum today.
At some point, we will also want to run a
  
  Draft   Wed Jul 11 18:13:19 2018 keerthanaSummaryAUXGouy Phase Measurements from AUX-Laser ScansFrom the Measurement Jon made, FSR is 3.967
MHz and the Gouy phase is 52 degrees. From
this, the length of the Y-arm cavity
  
  14053   Wed Jul 11 16:50:34 2018 poojaUpdateCamerasUpdate in developing neural networksAim: To develop a neural
network that resolves mirror motion from
 graphs.pdf 
  14052   Wed Jul 11 16:23:21 2018 aaronUpdateOMCCoordination of the Output Mode-cleaner Mirror Insertion Expedition (COMMIE)I started this document on my own with
notes as I was tracing the beam path through
the output optics, as well as some notes
  
  14051   Wed Jul 11 15:57:00 2018 aaronUpdateOMCReviving OMC electronicsGautam showed me the electronics racks
for the OMC PZTs and DAQ. I'm in the
process of chasing down what channels we
  
  14050   Tue Jul 10 23:44:23 2018 AnnalisaConfigurationThermal CompensationHeater setup assembly[Annalisa, Koji]

Today both the heater and the reflector
were delivered, and we set down the setup
 8x 
  14049   Tue Jul 10 16:59:12 2018 Izabella PastranaHowToComputer Scripts / ProgramsTaking Remote TF Measurements with the Agilent 4395AI copied the netgpibdata folder
onto rossa (under the directory ~/Agilent/),
which contains all the necessary scripts
  
  14048   Tue Jul 10 14:20:09 2018 steveUpdateGeneralprojector light bulb replacedBulb replaced at day 110  We have
now spare now.

 
  
  14047   Mon Jul 9 17:29:28 2018 Udit KhandelwalSummaryTip-TIltTipTilt mirror holder final changesFinal Summary of changes to mirror holder
in Tip-Tilt holder.

Determining minimum range
 d_COM.png1-1.png1-2.png2-1.png 
  14046   Mon Jul 9 12:36:32 2018 poojaUpdateGeneralProjector light bulb blown outProjector light bulb blown out today.   
  14045   Sun Jul 8 22:27:25 2018 keerthanaUpdate AUX diagram(Analisa, Keerthana, Sandrine)

So far we tried four different
techniques to scan the AUX laser. They are,
 PLL-single_demodulation.pdfPLL-double_demodulation.pdf 
  14044   Sun Jul 8 12:20:12 2018 JonSummaryAUXGouy Phase Measurements from AUX-Laser ScansThis note reports analysis of cavity scans
made by directly sweeping the AUX laser carrier
frequency (no sidebands). The measurement
 yarm_aux_carrier_trans.pdfprmi_aux_carrier_trans.pdfdrmi_aux_carrier_trans.pdf 
  14043   Sat Jul 7 19:50:38 2018 AnnalisaConfigurationThermal CompensationStudy about the Thermal projection setup and its effect on the cavityI made some simulation to study the change
that the heater setup can induce on the Radius
of Curvature of the ETM.
 6x 
  14042   Fri Jul 6 19:39:37 2018 Udit KhandelwalSummaryGeneralCAD drawings of cantilever suspension requiredRequest
to Koji to acquire the drawings or 3D CAD
of the cantilever suspensions of the Tip-Tilt
  
  14041   Fri Jul 6 12:12:09 2018 AnnalisaConfigurationThermal CompensationThermal compensation setupI tried to put together a rudimentary heater
setup. 

As a heating element, I used the
 IMG_1887.jpgIMG_1884.jpgIMG_1883.jpgIR20180706_0358_labels.png 
  14040   Thu Jul 5 17:58:04 2018 keerthana, sandrineUpdateelog (Analisa, Sandrine, Keerthana)

Today Annalisa helped us to understand
the new set up used to make the frequency
 setup1.jpgsetup2.jpg 
  14039   Thu Jul 5 17:33:36 2018 keerthana, sandrineUpdateelogLights not working
N/S ARM FL.
N/S ARM
INC.


These two lights inside
the 40m-lab are not working.
  
  14038   Thu Jul 5 10:15:30 2018 gautamUpdateSUSPRM watchdog trippedPRM watchdog was tripped around 7:15am
PT today morning. I restored it.
 PRM_watchdogTrip.png 
  14037   Wed Jul 4 20:48:32 2018 poojaUpdateCamerasMedm screen for GigE(Gautam, Pooja)

Aim: To develop medm screen for
GigE.
 sitemap.pngGigE_macros.pngCUST_CAMERA.png 
  14036   Wed Jul 4 19:11:49 2018 JonUpdateAUXMore Testing of AUX-Laser Mode ScanningMore progress on the AUX-laser cavity scans.

Changes to the Setup


For
scans, the Agilent is now being used as a
 yarm_trans_70uW.pdfprc_trans_9mW.pdfyarm_carrier_trans_70uW.tar.gzprc_carrier_trans_9mW.tar.gz 
  14035   Tue Jul 3 11:59:10 2018 JonUpdateAUXAUX Carrier Scan of Y-Arm CavityI made the first successful AUX laser scan
of a 40m cavity last night.

Attachment #1 shows the measured
 yarm_carrier_trans.pdfAG4395A_02-07-2018_185504.txt 
  14034   Mon Jul 2 09:01:11 2018 SteveUpdateSUSITMY_UL sensorThis bad connection is coming back




 ITMY_ULcripingback.png 
  14033   Fri Jun 29 18:16:32 2018 JonConfigurationPSLChanges to AUX Optical Layout on PSL TableIn order to use the 0th-order deflection
beam from the AOM for cavity mode scans,
I've coaligned this beam to the
 PSL_AUX_SETUP_CHANGE.pdf 
  14032   Thu Jun 28 16:48:27 2018 gautamUpdateSUSSOS cage towers For the upcoming vent, we'd like to
rotate the SOS towers to correct for the
large YAW bias voltages used for DC alignment
  
  14031   Thu Jun 28 13:12:20 2018 SteveUpdatesafetysurf safety trainingShruti and Sandrine received 40m specific
basic safety training this morning.

  
  14030   Thu Jun 28 11:05:48 2018 shrutiUpdatePEMSeismometer temp control equipmentEarlier today I cleared up most of the
equipment at the X end near the seismometer
to make the area walkable. 
  
  14029   Thu Jun 28 10:28:27 2018 ranaUpdateCDS vacuum pneumatic N2 pressurewe disabled logging the N2 Pressure to
a text file, since it was filling up disk
space. Now it just sends an email to our
  
  14028   Thu Jun 28 08:09:51 2018 SteveUpdateCDS vacuum pneumatic N2 pressureThe fardest I can go back on channel C1:
Vac_N2pres is  320 days

C1:Vac-CC1_Hornet Presuure gauge
 320d_N2.png 
  14027   Wed Jun 27 21:18:00 2018 gautamUpdateCDSLab maintenance scripts from NODUS---->MEGATRONI moved the N2 check script and the disk
usage checking script from the (sudo) crontab
of 
  
  14026   Wed Jun 27 19:37:16 2018 KojiConfigurationComputersNew NAT router installed[Larry, Koji]

We replaced the NAT router between
martian and the campus net. We have the administrative
 P_20180627_193357.jpg 
  14025   Wed Jun 27 19:05:20 2018 ranaUpdateComputersrossa: SL7.3 upgrade continues: DTT is backUNELOGGED: someone has changed
Pianosa from Ubuntu/Dumbian into SL7. Might
be hackers.
  
  14024   Wed Jun 27 18:12:04 2018 gautamUpdateElectronicsCoil driver dewhiteningSummary:

I've been thinking about what
we need to do to the de-whitening boards
 DeWhiteningSketch.pdf 
  14023   Tue Jun 26 22:06:33 2018 ranaUpdateComputersrossa: SL7.3 upgrade continues: DTT is backI used the following commands to
get diaggui to run on rossa/SL7:

controls@rossa|lib64>
  
  14022   Tue Jun 26 20:59:36 2018 aaronUpdateOMCprep for vent in a couple weeksI checked out the elog from the vent in
October 2016 when the OMC was removed from
the path. In the vent in a couple weeks,
  
  14021   Tue Jun 26 17:54:59 2018 poojaUpdateCamerasDeveloping neural networksAim:  To find a model that trains
the simulated data of Gaussian beam spot
moving in a vertical direction by the application
 NN_noise_diag.zip 
  14020   Tue Jun 26 17:20:33 2018 JonConfigurationCamerasLLO Python Camera Software is WorkingThanks to a discussion yesterday with Joe
Betzweiser, I was able to identify and fix
the remaining problem with the LLO GigE camera
  
ELOG V3.1.3-