40m QIL Cryo_Lab CTN SUS_Lab TCS_Lab OMC_Lab CRIME_Lab FEA ENG_Labs OptContFac Mariner WBEEShop
  40m Log, Page 119 of 335  Not logged in ELOG logo
ID Date Author Type Category Subject
  10896   Tue Jan 13 15:11:30 2015 diegoUpdateLSCTransitioned to ASDC MICH (PRMI and PRFPMI)

These are the parameters of the UGF servos we used last night:

DOF / Parameters Exc. Frequency (Hz) Exc. Gain Loop Gain
DARM 110.1 0.025 -0.03
MICH n/a n/a n/a
PRCL 150.001 2.0 -0.03
CARM 115.1 0.01 -0.03


Some tweaking of such parameters and the commissioning of the MICH servo will be done soon; an elog post about the UGF scripts/medm screens also will be done soon.

  10895   Tue Jan 13 14:01:20 2015 manasaUpdateGeneralAUX Y + PSL beat note at 1064nm: needs work

I'm super excited about this new frequency readback, but I'm not sure that it's reliable yet.  Without touching any settings, the readback is currently saying 78.6MHz, and is changing slightly (as is the FSS Slow Temp), so something is working.  However, the beatnote as measured on the spectrum analyzer is 158.2MHz.  So, either the calibration or the tracking or something isn't quite finished being tuned yet.

It's going to be super awesome when we have this though!!

As Jenne pointed out, this is still not fully tuned. 

For example, I found today that the frequency counter requires more power at the input >= -20dBm to measure frequency inputs < 40 MHz. Since the RFPD gives ~ -40dBm at its output, the ~20dB gain amplifier will not be enough to measure low frequencies in case the beat power at the PD drops (which is very much possible when the alignment drifts or things move around on the PSL table).  So I am shopping for an RF amplifier with higher gain to replace the current one. In the meantime, I will test the PID loop for set point frequency > 40MHz.

I have also observed the frequency difference between the measured frequencies on FC and the spectrum analyzer. I am not sure where this comes from as yet. 

At this point, the FC readout is only reliable enough to find a beatnote that is lost on the spectrum analyzer.

  10894   Tue Jan 13 13:22:54 2015 JenneUpdateGeneralAUX Y + PSL beat note at 1064nm: needs work

I'm super excited about this new frequency readbacklaugh, but I'm not sure that it's reliable yetfrown.  Without touching any settings, the readback is currently saying 78.6MHz, and is changing slightly (as is the FSS Slow Temp), so something is working.  However, the beatnote as measured on the spectrum analyzer is 158.2MHz.  So, either the calibration or the tracking or something isn't quite finished being tuned yet.cheeky

It's going to be super awesome when we have this though!!cool

  10893   Tue Jan 13 10:28:02 2015 manasaUpdateGeneralAUX Y + PSL beat note at 1064nm

I plan to use the Minicircuits ZFL-1000ln that is on the IOO rack but not being used (This was used for green beatnote amplification but is not required/used anymore) to amplify the RF signal to the frequency counter.
If anyone has any objections to using this amplifier for the frequency counter, let me know.

The above mentioned amplifier has been used to amplify the input to the frequency counter. The frequency counter is now getting an input that it can read.

I have done an edit to the ALS medm screen and the PSL and AUX Y laser beat frequency is now readable.

  10892   Tue Jan 13 04:57:26 2015 ericqUpdateCDSAll FE diagnostics back to green

I was looking into the status of IPC communications in our realtime network, as Chris suggested that there may be more phase missing that I thought. However, the recent continual red indicators on a few of the models made it hard to tell if the problems were real or not. Thus, I set out to fix what I could, and have achieved full green lights in the CDS screen. 

This required:

  • Fixing the BLRMS block, as was found to be a problem in ELOG 9911 (There were just some hanging lines not doing anything)
  • Cleaning up one-sided RFM and SHMEM communications in C1SCY, C1TST, C1RFM and C1OAF

The frontend models have been svn'd. The BLRMs block has not, since its in a common cds space, and am not sure what the status of its use at the sites is...

  10891   Tue Jan 13 03:58:27 2015 JenneUpdateLSCTransitioned to ASDC MICH (PRMI and PRFPMI)

[Jenne, Diego, EricQ]

Hopefully there will be more later, but Chiara just went down (network? other?  Q is in there right now looking at it), so this is a so-far-tonight elog.

We have successfully transitioned MICH over from REFL33Q to ASDC in both the PRMI and PRFPMI configurations.  Next up is to start reducing the CARM offset.

Resetting the REFL demod phases

I have been unable to lock the PRMI for more than teeny blips since Thursday.  So, tonight I finally got it to lock with MICH on AS55Q and PRCL on REFL33I, and used that to set the demod phases. 

Input matrix 1*AS55Q 1*R33I
Gain -7 -0.022
DoF trigger POP22I; 80up, 2down POP22I; 80up, 2down
FM trigger FM 2,6,8; 100up, 2down; 0.3sec FM 2,6,9; 100up, 2down; 0.01sec
Normalization n/a n/a
Output matrix 0.5*BS, -0.2625*PRM 1*PRM
UGF servo n/a


Setting the demod phases, I used an oscillation of 100 cts to PRM, at 400.123 Hz.

REFL 33 demod phase started at 148deg, now 133.2deg.

REFL165 phase started at -105.53, now -172.

No signal in REFL55????  Time series and spectra both look just like noise.  Need to check alignment of beam on PD, or if cables unplugged!!

REFL11 phase started at 16.75, now 18.9deg.

Was then able to lock on REFL 33 I&Q, like normal.

Input matrix 1*R33Q 1*R33I
Gain 2.5 -0.02
DoF trigger POP22I; 80up, 2down POP22I; 80up, 2down
FMs FM 4,5 on FM 4,5 on
FM trigger FM 2,6,8; 100up, 2down; 0.3sec FM 2,6,9; 100up, 2down; 0.01sec
Normalization n/a n/a
Output matrix 0.5*BS, -0.2625*PRM 1*PRM
UGF servo n/a


Transitioning PRMI from REFL33Q to ASDC

With the PRMI locked on REFL33 I&Q, I found that a MICH offset of -5 counts gives a minimum in ASDC.  From my earlier elog this evening (http://nodus.ligo.caltech.edu:8080/40m/10887), I expect the minimum to be at +1.4nm.  This is only one point though, so I don't know the calibration of the MICH offset yet (we should get this calib during the day by looking at MICH-only).  Anyhow, this informed which side was positive and negative relative to my Optickle plots, so I know that I wanted positive offset in the MICH servo.

I was able to comfortably hold lock at +20 counts.  Looking at a calibration line at 143.125 Hz, I determined that I wanted the matrix element for ASDC to be -0.05.  After I made that transition using ezcastep, I put the POPDC normalization in.  At the time, POPDC was about 151counts, so I put 1/151 in the POPDC->Mich matrix element.

So, here were the final lock parameters.  Note that in PRMI-only, you can acquire lock like this, and with a variety of MICH offsets:

Input matrix -0.05 * ASDC 1*R33I
Gain 2.5 -0.02
DoF trigger POP22I; 80up, 2down POP22I; 80up, 2down
FMs FM 4,5 on FM 4,5 on
FM trigger FM 2,6,8; 100up, 2down; 0.3sec FM 2,6,9; 100up, 2down; 0.01sec
Normalization  0.0066 n/a
Output matrix 0.5*BS, -0.2625*PRM 1*PRM
UGF servo n/a


Locking PRMI part of PRFPMI

Since the PRMI has been fussy, I'm including a brief note on the PRMI settings when the arms are held with ALS off by roughly 3nm.  To get to this point, we just ran the usual carm_cm_up script, and didn't let it run anymore when it asked for confirmation that PRMI was locked.

Input matrix 1*R33Q 1*R33I -1*alsX+1*alsY 1*alsX+1*alsY
Gain 2.5 -0.012 8 8
DoF trigger POP22I; 80up, 2down POP22I; 80up, 2down n/a n/a
FMs FM 4,5 on FM 4,5 on FM 1,2,3,5,6 FM 1,2,3,5,6
FM trigger FM 2,6,8; 50up, 2down; 0.3sec FM 1,2,6,9; 50up, 2down; 0.01sec n/a n/a
Normalization n/a n/a n/a n/a
Output matrix 0.5*BS, -0.2625*PRM 1*PRM 1*etmx+1*etmy -1*etmx+1*etmy
UGF servo n/a set to 150Hz n/a n/a

With MICH offset of -30 counts, AS port is pretty bright.  ASDC dark offset is set to -475.4 by the LSCoffsets script. with MICH offset = 0, ASDC_OUT is around 300counts.  But, with MICH offset = -30, ASDC_OUT is about 525 counts.  So, I put that 525 counts into the ASDC filterbank offset (so it is now the dark offset + this extra offset), so the ASDC offset is currently around -1,000.  This makes the ASDC signal roughly zero when I am ready to transition MICH over to it.  In principle I should probably set it so the average is the same as the MICH offset, but the noise is so high relative to that offset, that it doesn't matter.

After this, we engaged the CARM and DARM UGF servos.  MICH was gain peaking, so I think we might want to turn that one on too, rather than my by-hand turning down the gain.

The transition has been successful 4 or 5 times with the arms held off resonance at 3nm.  Once, we reduced the CARM offset as low as 1.7 (and had to lower the MICH gain to 1.5), but we were still hearing a woomp-woomp sound.  Not sure what that was from.  At this point, Chiara died, so we lost lock.  After that, we re-acquired lock a few more times, but MC keeps losing it.  We are still able to make the MICH to ASDC transition though, which is good.

The transition won't work if the PRCL UGF servo is not on.  The gain multiplier goes from about 1.1 up to 2.4, so the PRCL gain is certainly changing through the transition.

Diego has written up scripts for the individual UGF servos (look for an elog from him separately), so now the carm_cm_up script goes as far as locking the PRMI on REFL33 I&Q, and then it starts to transition.  PRCL UGF is engaged, MICH offset is set to -30 counts, MICH is transitioned to ASDC, POP normalization engaged, CARM UGF servo turned on, and DARM UGF servo turned on.  There are "read"s in the script before each step, so you can stop whenever you like.

Here's the final configuration for the PRFPMI while the arms are held at 3nm, with MICH on ASDC (so after the transition):

Input matrix 0.27*ASDC 1*R33I -1*alsX+1*alsY 1*alsX+1*alsY
Gain 2.5 -0.015 8 8
DoF trigger POP22I; 80up, 2down POP22I; 80up, 2down n/a n/a
FMs FM 4,5 on FM 4,5 on FM 1,2,3,5,6 FM 1,2,3,5,6
FM trigger FM 2,6,8; 50up, 2down; 0.3sec FM 1,2,6,8,9; 50up, 2down; 0.01sec n/a n/a
Normalization 0.0042*POPDC n/a n/a n/a
Output matrix 0.5*BS, -0.2625*PRM 1*PRM 1*etmx+1*etmy -1*etmx+1*etmy
UGF servo n/a set to 150.001Hz set to 115.1Hz set to 110.1


The transition for MICH to ASDC has been successful with the arms held off resonance several times tonight. It's all part of the carm_cm_up script now. I think that if we hadn't lost about an hour of time and our momentum, we would have gotten farther.  I have high hopes for tomorrow night!

  10890   Tue Jan 13 03:47:46 2015 ericqUpdateCDSInstalled new ethernet driver on Chiara

Chiara threw another network hissy fit. Dmesg was spammed with a bunch of messages like eth0: link up appearing rapidly. 

Some googling indicated that this error message in conjuction with the very ethernet board and driver that Chiara had in use could be solved by updating with an appropriate driver from the manufacturer.

In essence, I followed steps 1-7 from here: http://ubuntuforums.org/showthread.php?t=1661489

So far, so good. We'll keep an eye out to see how it works...

  10889   Tue Jan 13 01:58:16 2015 ericqUpdateComputer Scripts / ProgramsCdsutils upgraded to 382

I've upgraded our cdsutils installation to v382; there have been some changes to pydv which will allow me to implement the auto y-scaling on our lockloss plots. 

After some brief testing, things seem to still work...

  10888   Tue Jan 13 01:11:51 2015 diegoUpdateLSCResponse of error signals to MICH EXC

For several MICH offsets, I measured the response of REFL33Q, ASDC and the ratio ASDC/POPDC to a MICH EXC. It appears that there is no frequency-dependent effect. The plots for MICH_OFFSET = 0.0 and 2.0 are slightly lower in magnitude: the reason is they were the first measurements done, and after that a little realignment of BS was necessary, so probably that is the reason.



Attachment 1: MICH_to_REFL33Q_ASDC_12Jan2015_1.pdf
Attachment 2: MICH_to_REFL33Q_ASDC_12Jan2015_2.pdf
Attachment 3: MICH_to_REFL33Q_ASDC_12Jan2015_3.pdf
  10887   Tue Jan 13 00:42:15 2015 JenneUpdateLSCError signals for MICH with variable finesse technique

In order to know where we should try to make the transition from REFL##Q to ASDC for MICH, I did a quick Optickle simulation to see what the error signals will look like.

The idea is to try to lock the PRMI on a single REFL diode (ex. REFL33 I&Q) with some MICH offset, and then transition over to ASDC.  As soon as we have completed the transition, we can engage the normalization matrix to normalize ASDC by POPDC, and also increase the MICH offset if we want.  Unfortunately, we do not as yet have the ability in our model to independently normalize different error signals, and then blend them, so we have to turn on the normalization after we've transitioned.

Here is the situation for PRMI-only:

You can see that REFL33Q has a slightly wider range than REFL165Q.  It seems like we can perhaps try to make the transition around -15nm or so.  Note that the error signals are not quite symmetric about 0nm, so we can use that to help determine what + and - mean.  We expect that we need to add about 1nm offset to REFL33Q to get a true minimum in ASDC, so the sign of the digital offset that we need will tell us if there is a sign flip or not between the digital offset and this x-axis. 

After we get this to work (hopefully in the next hour or so....), we will want to try the same thing with the arms held off resonance. 

Usually we lock the PRMI at an offset of about 3nm:

However we could do it lower, perhaps around 1nm (which is where we currently are doing our CARM/DARM ALS->IR signals transitions):

At some point, we will arrive at 0nm CARM offset, when we'll want to transition back to RF signals (although probably we could jump straight to a 1f signal, not plotted):

The moral of the story here is that I'm not sure how we were ever successfully locking MICH on REFL165Q, unless my phase-setting in Optickle is way off.  Certainly it looks like we should be sticking with REFL33 for PRFPMI.  Also, since we have an offset in REFL33Q anyway (which we have seen and have commented on before), at 3nm CARM offset it looks like we could try to just do the jump without any extra digital offset.  Here's a zoom of the 3nm situation:

  10886   Mon Jan 12 18:11:25 2015 ericqUpdateASCTest Mass -> Transmon QPD TFs measured

We want to have some angular control of the arms during lock acquistion. 

In single arm lock, Diego and I shook the TMs and measured how the QPDs responded. (I would've liked to do a swept sine in DTT, but the user envelope function still isnt' working!)

For now, we can close simple loops with QPD sensor and ITM actuator, but, as Rana pointed out to Diego and me today, this will drive some amount of the angular cavity degree of freedom that the QPD doesn't sense. So, ideally, we want to come up with the right combination of ITM and ETM motion that lies entirely within the DoF that the QPD senses.

I created a rudimentary loop for Yarm yaw, was able to get ~20Hz for the upper UGF, a few mHz for the lower, but it was starting to leak into the length error signal. Further tweaking will be neccesary...

Attachment 1: Jan12_singleArmSensing.pdf
Attachment 2: Jan12_singleArmSensing.xml.zip
  10885   Fri Jan 9 19:18:51 2015 JenneUpdatePSLPMC realigned

A few hours ago I tweaked up the alignment to the PMC.  It was really bad in pitch, and the transmission was down to about 0.711.

  10884   Fri Jan 9 14:13:02 2015 manasaUpdateGeneralALS noise at ~30Hz

Before starting to move things around the PSL table, I measured the ALS out of loop noise for reference. The noise spectrum showed excess noise around 30Hz.  The traces in blue were taken before I went in and those in red were taken after my work.

I also looked at the power spectrum of LSC-TRY_OUT to see if the noise is from the IR lock itself and there was nothing suspicious with it. 

Since the green transmission was 50% lower than the usual, I touched the steering mirrors for green at the Y end table to get a better transmission and beat signal. The noise still hasn't disappeared. 

I am not sure if this could be from our neigbors who have been running rock experiments since morning. We should check back to see if this noise disappears once they shut down.

DTT xml files are available in directory /users/manasa/data/150109/

Attachment 1: ALSYoutLoop.png
Attachment 2: LSC_TRY.png
  10883   Fri Jan 9 14:01:17 2015 manasaUpdateGeneralAUX Y + PSL beat note at 1064nm

I worked around the PSL table today.

The Y+PSL output from the optical fiber module for FOL was fed to the input of the Thorlabs FPD310
200uW of incident light on the RFPD gave an RF signal of -70dBm as measured on a spectrum analyzer.

I swapped the beam splitter along the PSL path so that the incident power on the RFPD is ~1.5mW (Maximum incident power that the PD can tolerate is ~2mW).
This RF signal generated was - 43dBm which is still small for the input to the frequency counter module.

I checked this with a function generator and found that the frequency counter requires around -25 to -30 dBm at the input.

I plan to use the Minicircuits ZFL-1000ln that is on the IOO rack but not being used (This was used for green beatnote amplification but is not required/used anymore) to amplify the RF signal to the frequency counter.
If anyone has any objections to using this amplifier for the frequency counter, let me know.


  10882   Fri Jan 9 10:52:37 2015 SteveUpdateSUSPIT trend plots at the ends

100 and 10 days trends of ETMX and ETMY_SUSPIT.  One can see clearly the earthquaks of Dec.30 and 31 on the 10 day plot. You can not see the two shakes  M3.0 & M4.3 of Jan. 3 

The long term plot looks OK , but   the 10 day plot show the problem of ETMX as it was shaken 4 times.


Attachment 1: susPITends.png
  10881   Thu Jan 8 23:02:30 2015 diegoUpdateSUSSUS Drift Monitor

The MEDM screen has been updated: the new buttons, one for each optic, call the scripts/general/SUS_DRIFTMON_update_reference.py script, which measures (and averages) for 30s the current values of the POS/PIT/YAW drifts, and then sets the average as the new reference value.


  10880   Thu Jan 8 19:41:50 2015 ericqUpdateGeneralinane LSCoffsets script removed

The restored offset script used old tdsavg calls that our workstations can't do, and didn't include things like the transmon QPDs. I've written yet another offset script that uses cdsutils averaging to do the thing, and committed to the svn. 

  10879   Thu Jan 8 19:02:42 2015 JaxSummaryElectronicsMC demod modifications

Here's a summary of the changes made to the D990511 serial 115 (formerly known as REFL 33), as well as a short procedure. It needed tuning to 29.5MHz and also had some other issues that we found along the way. 

So here's a picture of it as built:

The changes made are:

1. U11 and U12 changed from 5MHz LP to 10 MHz LP filters.

2. Resistors R8 and R9 moved from their PCB locations to between pins 1 (signal) and 3 (ground) of U11 and U12, respectively. These were put in the wrong place for proper termination so it made sense to shift them while I was already replacing the filters.

Also, please note- whoever labeled the voltages on this board needed an extra cup of coffee that day. There are two separate 15V power supplies, one converted from 24V, one directly supplied. The directly supplied one is labeled 15A. This does NOT mean 15 AMPS.

Transfer functions:

Equipment: 4395A, Signal generator (29.5 MHz), two splitters, one mixer

You can't take the TF from PD in to I/Q out directly. Since this is a demod board, there's a demodulating (downconverting) mixer in the I and Q PD in paths. Negligible signal will get through without some signal applied to the L input of the mixer. In theory, this signal could be at DC, but there are blocking capacitors in the LO in paths. Therefore, you have to upconvert the signal you're using to probe the board's behavior before it hits the board.  Using the 4395A as a network analyzer, split the RF out. RFout1 goes to input R, RFout2 goes to the IF port of the mixer. Split the signal generator (SG). SG1 goes to LO in, SG2 goes to the L port of the mixer. The RF port of the mixer (your upconverted RFout2) goes to PD in, and the I/Q out goes back to the A/B port of the 4395A - at the same frequency as the input, thanks to the board's internal downconversion. 

Phase measurement:

Equipment: Signal generator (29.5 MHz), signal generator (29.501 MHz), oscilloscope

Much simpler: 29.5 MHz to the LO input (0 dBm), 29.501 MHz to the PD input (0 dBm), compare the phases of the I/Q outputs on the oscilloscope. There are four variable capacitors in the circuit that are not on the DCC revision of the board - C28-31. On the LO path, C28 tunes the I phase, C30 tunes the Q phase. On the PD path, C29 and 31 appear to be purely decorative - both are in parallel with each other on the PD in Q path, I'm guessing C29 was supposed to be on the PD in I path. Fortunately, C28 and C30 had enough dynamic range to tune the I/Q phase difference to 90 degrees.

Before tuning:

After tuning:


  10878   Thu Jan 8 09:24:40 2015 jamieUpdateComputer Scripts / ProgramsELOG 3.0

I've installed the very fresh ELOG 3.0, for nothing else than the new built in text editor which has a LATEX capable equation editor built right in. 

Check out this sweet limerick: 

\int_{1}^{\sqrt[3]{3}}t^2 dt\, \textbf{cos}(\frac{3\pi}{9}) = \textbf{ln}(\sqrt[3]{e})

\int \omega \epsilon \varepsilon \Gamma

  10877   Thu Jan 8 03:40:50 2015 ericqUpdateComputer Scripts / ProgramsELOG 3.0

I've installed the very fresh ELOG 3.0, for nothing else than the new built in text editor which has a LATEX capable equation editor built right in. 

Check out this sweet limerick: 

\int_{1}^{\sqrt[3]{3}}t^2 dt\, \textbf{cos}(\frac{3\pi}{9}) = \textbf{ln}(\sqrt[3]{e})

  10876   Thu Jan 8 03:09:07 2015 JenneUpdateLSCToward variable finesse locking

[Jenne, EricQ, Rana]

Tonight we started prepping for an attempt at variable finesse locking. 

The idea is to put in a MICH offset and hold the lock with ASDC/POPDC (so that the offset can be larger than if we were just using RF signals).  This reduces the PRC buildup, which reduces / removes the double cavity resonance problems while reducing the CARM offset. 

  • So.  Today, I pulled out the POP22 razor blade so that we can use the Thorlabs PD as POPDC, without the yaw coupling.  Our other option is to use the POP QPD SUM, but that would require some model changes and more importantly it's not a particularly low noise readout path.
  • We re-set the analog whitening gains for ASDC and POPDC.
    • For ASDC, we want the half-fringe in the PRMI case to be not saturating.  We chose 18dB (it had been the default 0dB).
    • For POPDC, Rana and I saw that it was saturating all the time with the 33dB that it had when the carrier became resonant.  This was never really a problem in the past, but if we use it for normalization, we get glitches that knock us out of lock every time POPDC saturated.  So, now POPDC is at 0dB.  It still occasionally saturates when the PRMI is flashing, but we can't get lower than 0dB without going and putting an ND filter on the PD.
  • We turned off the analog whitening filters and digital unwhitening for both ASDC and POPDC.  We can consider turning them back on later after we have acquired lock if we need them, but we need them off for acquisition.
  • Locked MICH with ASDC/POPDC.  Good.  Stays locked even if PRM is flashing.
  • Locked PRMI with PRCL on REFL33I and MICH on ASDC/POPDC.
  • Locked arms, held off resonance with ALS, lock MICH with ASDC/POPDC. 
  • Failed to lock PRMI with arms held off resonance, using the new scheme (no transition, trying to directly acquire)
  • Locked PRMI on REFL33 I&Q with the arms held off resonance, and tried to transition MICH over to ASDC/POPDC, failed.
  • Confusion about the relative phase between REFL33Q and ASDC.  It looks like it is ~45deg at 100 Hz, or ~90 deg at 375 Hz.  Why isn't it 0 or 180?
  • Went back to PRMI-only, tried to map out fringe by changing MICH offset (tried while MICH was on both REFL33 and ASDC/POPDC).  Not really sure where we are on the fringe.

MICH locked on ASDC normalized by POPDC, PRM and ETMs (and SRM) all misaligned.

MICH offset of -20

MICH input = -0.04*ASDC normalized by 0.1*POPDC.

MICH gain = +5

MICH always triggered on (no triggering for DoF), but FM8 (CLP400) triggered to come on after lock (didn't write down the values).


PRMI locked with MICH on ASDC normalized by POPDC, PRCL on REFL33I, ETMs and SRM misaligned.

MICH offset of -10

MICH input = -0.04*ASDC normalized by 0.1*POPDC.

PRCL input = 1*REFL33I

MICH gain = +5

PRCL gain = -0.4 (factor ten times the regular value)

MICH always on, PRCL triggered on POP22.  MICH FM8 and PRCL FM1,2,6,9 triggered on.

Gives POPDC of about 20 counts, POP22 of about 12 counts, ASDC of about 500 counts.


Arms held at 3nm, MICH locked on ASDC/POPDC, PRM and SRM misaligned.

MICH offset of -10

MICH input = -0.04*ASDC normalized by 0.1*POPDC.

MICH gain = +5

MICH always on, PRCL triggered on POP22.  MICH FM8 and PRCL FM1,2,6,9 triggered on.


Arms held at 3nm, attempt at PRMI lock with MICH on ASDC/POPDC.

Failed.  Tried mostly same MICH gains as arms+mich, and PRCL at 10* normal gain.


Arms held at 3nm, PRMI locked with REFL 33 I&Q, attempt at transition to MICH on ASDC/POPDC.

Failed.  At first, I was putting in the TF line at ~375Hz, but we looked at the full transfer function between 100Hz and 1kHz, and there was a weird dip near 300Hz from PRCL-MICH loop coupling.  Here we were seeing that the phase between REFL33Q and ASDC was ~90 degrees.  What?

Tried putting the TF line at ~100 Hz (since MICH UGF is in the few tens of Hz anyway, so 100 is still above that), but still get weird relative phase.  Here it seems to be about 45 degrees when I inject a single line, although it didn't seem like a weird phase when we did the full swept sine earlier.  Maybe I was just not doing something right at that point??

Anyhow, no matter what values I tried to put into the input matrix (starting with REFL33I&Q, trying to get MICH to ASDC/POPDC), I kept losing lock.  This included trying to ramp up the MICH offset simultaneously with the matrix changing, which was meant to help with the PRCL gain change.  Q has since given us MICH and PRCL UGF servos.



  • Why is there some weirdo phase between REFL33Q and ASDC at 100Hz?  Was I just being a spaz?
  • With PRMI-only, figure out how to transition from REFL33 I&Q over to MICH on ASDC/POPDC.
  • Then hold the arms off resonance, and do the same transition.  (First make sure we're at a good place on the fringe)
  • Lower the CARM and DARM offsets, transition them to RF, engage CARM AO path.
  • Reduce MICH offset, transition to RF.
  • Celebrate (maybe).
  10875   Thu Jan 8 02:52:09 2015 ericqUpdateLSCUGF Servo for LSC

I added UGF servos for the DRMI DoFs, after creating a library block for the servos. I also deleted the FMs before the phase rotation, since we can just do it afterwards in other existing FMs. I've only added the MICH and PRCL buttons to the LSC screen because in the end, I feel like a dropdown is better, but I just wanted to get it running quickly tonight. The LSC model and the UGF block have been committed to the svn. 

We were able to use the PRCL UGF servo successfully, as Jenne was exploring MICH offset space. 

  10874   Wed Jan 7 21:13:35 2015 ranaUpdateGeneralinane LSCoffsets script removed


 A few things that I have neglected to ELOG yet:

  • scripts/offsets/LSCoffsets is a new script that uses ezcaservo to set FM offsets of our LSC PDs. It still warns about large changes, and lets you revert. It reads the FM gain to pick the right gain for the ezcaservo call. 

 We never, ever want to use ezcaservo to do this. IN fact, we twice have already deleted scripts where people have implemented these (sometimes) unstable servos. Also, since this change had never been committed to the SVN, I just deleted it and updated from the SVN to get back the script that doesn't use any servos.

I'm going to periodically delete locking scripts that are not committed to the SVN since anyone who is too lazy to use the SVN probably can't write code worth using.

  10873   Wed Jan 7 19:49:09 2015 manasaUpdateGeneralX end space issues

I have attached a photo of the ETMX table. The path of the 1064nm light rejected after the doubler and the green light are indicated for reference.

The fiber mount can only be mounted in the green space shown in the picture.

Calculating lens solutions for coupling the 1064nm light rejected after the doubler into the fiber, a lens of f=12.5cm should be placed at z=15.31cm (measured from the waist in the doubler crystal) gives the best ~80% coupling. This falls in the blue region where there is not enough space to mount a lens

The region marked in orange has enough room for a lens; but the lens solutions give a coupling <10% which means there will be light scattering everywhere.

I am open to any suggestions on how to go about this.


  10872   Wed Jan 7 15:53:01 2015 JenneUpdateLSCDC PD analog settings exposed

I have added another block to the LSC screen (and made the corresponding sub-screen) to expose the analog settings for the DC photodiodes. 

Note that we have 2 open channels there, which are still called something like "PD2" and "PD3" from olden times.

If we ever chose to use those, we will probably want to change their names, in /cvs/cds/caltech/target/c1iscaux2/LSC_aux2.db and /cvs/cds/caltech/target/c1iscaux/LSC_aux.db

  10871   Wed Jan 7 14:41:46 2015 SteveUpdateGeneralOphir pmeter filter found



Ophir power meter gets new filter with calibration. This is not cheap. It was the second time we lost it.

Filter leash is attached.

 Some one already took  off the filter and did not care to put it back on. This is carelessness!

Missing filter found. Labeled drawer OPHIR in control room - behind soldering station-  with spare battery and filter

  10870   Wed Jan 7 14:35:44 2015 diegoUpdateSUSSUS Drift Monitor

The SUS Drift Monitor screen has been updated:

  • removed the old dead channels from the MEDM screen;
  • updated the SUS models with new 'mute' channels where the expected values should be put;
  • updated the MEDM screen with the new channels
  • values are still 0 since I don't know what these expected values should be, at this time


  10869   Wed Jan 7 14:16:27 2015 JenneUpdateLSCtrans QPDs realigned

Now that both end transmission QPDs have the line filters, I aligned them.

I locked and aligned the IR using the ASS, then went to each end table and put the beam in the center of the QPD.

  10868   Wed Jan 7 13:39:42 2015 ChrisUpdateLSCDARM phase budget

I think the dolphin and RFM transit times are double-counted in this budget. As I understand it, all IPC transit times are already built in to the cycle time of the sending model. That is, the sending model is required to finish its computational work a little bit early, so there's time left to transmit data to the receivers before the start of the next cycle. Otherwise you get IPC errors. (This is why the LSC models at the sites can't use the last ~20 usec of their cycle without triggering IPC errors. They have to allow that much time for the RFM to get their control signals down the arms to the end stations.)

For instance, the delay measurement in elog 9881 (c1als to c1lsc via dolphin) shows only the c1lsc model's own 61 usec delay. If the dolphin transfer really took an additional cycle, you would expect 122 usec.

And in elog 10811 (c1scx to c1rfm to c1ass), the delay is 122 usec, not because the RFM itself adds delay, but because an extra model is traversed.

Bottom line: there may still be some DARM phase unaccounted for. And it would definitely help to bypass the c1rfm model, as suggested in 9881.

  10867   Wed Jan 7 12:15:17 2015 manasaUpdateGeneralNew RF cables

I was working around the PSL table this morning.

1. I have fibers running from the Y end and the PSL table to the Optical Fiber Module for Frequency Offset Locking. 

Y+PSL out power is ~200uW. From the transimpedance and responsivity specs of the RFPD (ThorLabs FPD310), we expect ~100uW or -10dBm RF power. I have not hooked up the RF output to a spectrum analyser to confirm this as yet.

2. Also, Steve and I ran RF cables (LMR-195A) from the PSL table to the FC module on the IOO rack.


  10865   Wed Jan 7 11:20:22 2015 SteveUpdateLSCX arm T-QPD gets SM1 thread adapter

C1:SUS-ETMX_QPD is removed and internal SM1 thread adapter epoxied into position as it is at the Y end

This adapter will take FL1064-10 line filter holder

Line filter is attached and qpd needs alignment.

  10864   Wed Jan 7 09:44:33 2015 ericqUpdateLSCDARM phase budget

As Jenne mentioned, I created a model of the DARM OLG to see why we have so little phase margin. However, it turns out I can explain the phase after all.

Chris sent me his work for the aLIGO DARM phase budget, which I adapted for our situation. Here's a stacked-area plot that shows the contributions of various filters and delays on our phase margin, and a real measurement from a few days ago . 


This isn't so great! Informed by Chris's model, the digital delays look like: (Here I'm only listing pure delays, not phase lags from filters)

  • 64k cycle (End IOP)
  • 16k cycle (End isce[x/y])
  • 16k cycle x 2 (end to LSC through RFM) [See ELOG 10811]
  • 16k cycle (LSC)
  • 16k cycle (LSC to SUS through dolphin) [See ELOG 9881]
  • 16k cycle (SUS)
  • 16k cycle x2 (SUS to end through RFM)
  • 16k cycle (End isce[x/y])
  • 64k cycle (SUS IOP)
  • DAC zero order hold

This adds up to about 570usec, 20.5 degrees at 100Hz, largely due to the sheer number of computer hops the transmission loops involve. 

As a check, I divided the measured OLG by my model OLG, to see if there is any shape to the residual, that my model doesn't explain. It looks like it fits pretty well. Plot:


So, unless we undertake a bunch of computer work, we can only improve our transmission loops through our control filter design. 

Everything I used to generate these plots is attached. 

Attachment 3: 2015-01-DARMphase.zip
  10863   Wed Jan 7 03:09:15 2015 JenneUpdateLSCPRFPMI status & IFO status

As a warm-up after the holidays, before the real locking began, I installed 1064nm bandpass filters in front of the transmission QPDs to eliminate the stray green light that is there.

The Yend had threads epoxied to it, so that end should be good.  Steve is going to repeat that for the Xend QPD at some point.  Right now, the filter is just on a lens mount about 2cm away from the PD box aperture, since that's as close as I could get it.

Also, while I was at the Xend, I noticed that the transmission camera is gone.  I assume that it was in the way of Manasa's fiber work, and that it'll get put back somehow, sometime.  She elogged that she had removed it, but I mistakenly thought that it was already replaced.  We don't use that camera much, so I'm not worried.

  10862   Wed Jan 7 03:04:13 2015 JenneUpdateLSCTRY (thorlabs pd) weird noise

[Jenne, Diego, Rana]

This is a note about work done last night. 

We were starting to lock, and saw glitches in the Thorlabs TRY PD about once every 1/60th of a second.  It is not a sine wave, so it is not 60Hz line noise directly.  It looks like this:


Rana pointed out that this looks like it could be from a power supply that is converting AC to DC. 

We went down to the Yend, and noticed some weird symptoms.  So far, we do not know where the noise is coming from.  Rather, we are just using the QPD for locking.

* The noise comes and goes, particularly if someone is moving around at the end station.

* Moving the Thorlabs power supply farther from the HeNe power supply didn't do much.  Turning off and disconnecting the HeNe supply didn't make the noise go away, so we conclude that it is not the HeNe's fault.

* We suspected the loops of excess cable that were sitting on top of iscey, but moving the coils away from the computer did not make the noise go away.

* We removed a few disconnected BNC cables that were near or touching the end table, but that didn't fix things.

* We disconnected the PD's signal cable and pulled it out of the table enclosure, and then put it back.  Noise was gone when cable was disconnected (good), but it was back after plugging the cable back in.

* The noise still comes and goes, but we don't have to use the Thorlabs PD for locking, so we leave it for another day.

RXA: also moved the Thorlabs power supply to a different power strip and tried putting it closer/farther to the Uniblitz shutter controller. Another suspect is that its some PWM type noise from the doubler crystal temperature driver. Need to try turning off the heater and the Raspberry PI to if it effects the noise.

  10861   Wed Jan 7 02:56:15 2015 diegoUpdateLSCUGF Servo for DARM

 [Jenne, Diego]

Today we began implementing the UGF Servos. Things we did:

  • we updated the LSC model with both DARM and CARM servos, and moved them from after the control system to before it, at the level of the error signal;
  • we updated the medm screens; new buttons are located in the main LSC screen;
  • we started commissioning the DARM servo, at first using DARM for the lock of the single Y arm, then we moved on to the PRFPMI lock and the usual transition from ALS to Transmission;
  • although we had several lock losses during the night, we managed to tweak the parameters of the DARM UGF servo (phases, excitation, gains), which now seems to work sufficiently fine;
  • the filters added to the I and Q filter banks are a single lowpass in each, while the only filter in the main servio is a standard integrator;
  • we don't have a step response at the moment, but we can say that the settling time of the servo is in the range of 10 seconds;
  • we updated the ALSdown.py and ALSwatch.py scripts with a call to a new UGFdown.py script; this script, located in the scripts/PRFPMI folder, takes care of disabling the servos and putting the excitation to zero in case of a lock loss; re-enablement of such things must be done manually;
  10860   Wed Jan 7 02:54:09 2015 JenneUpdateLSCFiddling with DARM filters

One of the things that we had talked about last night was the totally tiny amount of phase margin that we have in the CARM and DARM loops.  DARM seemed to be the most obnoxious loop last night, so I focused on that today, although the CARM and DARM loops are pretty much identical.

(Q tells me via email that the phase budget has the same ~14 degree discrepancy between what we expect and what we measure as his estimate last night.  However, the Caltech network issues prevented his posting an elog.)

So, we definitely need to figure out where this 14 deg is going, but for now, I wanted to see if I could recover a couple of extra degrees just by modifying the filters.

The original filters do seem to eat a lot of phase:


The short version of the story is that I didn't leave the filters changed at all.  I reverted back to the last version of the filter file from Monday night, so currently everything is as it was.

I tried increasing the Q of the zeros on the cyan and brown filters, which would sacrifice some gain at ~20 Hz, but hopefully win us 10+ degrees of phase.  This gave me a dip of about a factor of 2 between the new and old filters (all servo filters combined added up to this factor of 2 in magnitude) between ~20Hz - 70Hz. 

When we were locked using DARM for just the Yarm (for the UGF servo commissioning), I took a spectra of the error signal (which was POY) as a reference, then loaded in my new filters.  For the most part, the spectra didn't change (which is good, since the magnitude of the filter didn't change much.).  The spectra was bigger though between 50-70Hz, in kind of a sharp bandpass-looking shape that I wasn't expecting.    I don't know exactly why that's happening.

Anyhow, we tried the new filters once or twice with the full IFO, but kept losing lock.  Since I clearly haven't put in enough thought yet for these (particularly, how much suppression do we really need? what are our requirements???), I reverted back to the filter file from last night.  We continued locking, and checking out the new UGF servo that Diego is elogging about.

  10859   Tue Jan 6 17:41:20 2015 JenneConfigurationCDSDTT doesn't do envelopes??

[Jenne, Diego]

We are working on trying out the UGF servos, and wanted to take loop measurements with and without the servo to prove that it is working as expected.  However, it seems like new DTT is not following the envelopes that we are giving it. 

If we uncheck the "user" box, then it uses the amplitude that is given on the excitation tab.  But, if we check user and select envelope, the amplitude will always be whatever number is the first amplitude requested in the envelope.  If we change the first amplitude in the envelope, DTT will use that number for the new amplitude, so it is reading that file, but not doing the whole envelope thing correctly.

Thoughts?  Is this a bug in new DTT, or a pebkac issue?

  10858   Tue Jan 6 10:04:39 2015 SteveUpdateIOOhappy IOO
Attachment 1: IOO.png
  10857   Tue Jan 6 03:13:09 2015 ericqUpdateLSCPRFPMI status & IFO status

Two plots from tonight:

Lock loss. Based on the fact that it looked like the DARM servo was running away, Rana posited an effective sign flip in the DARM loop, perhaps due to a parasitic angular feedback mechanism.



While Jenne was probing the IFO at lower powers, we noticed a sudden jump in ASDC. Found the GPS time and fed it to the lockloss plotter. Seems fairly evident that some sudden ETMX motion was to blame. (~2urad kick in yaw)


  10856   Tue Jan 6 03:09:17 2015 diegoUpdateLSCPRFPMI status & IFO status

 [Jenne, Rana, EricQ, Diego]

Tonight we worked on getting the IFO back in a working status after the break, and then tried some locking.

  • the MC is behaving better, it could stay in a stable condition for hours, even if a couple of times it lost lock, and one of them persisted for a little time;
  • we managed to get to arm power of 20ish, before losing lock (this happened a couple of times);
  • the main thing seems to be that we have only ~ 20 degrees of phase margin at UGF for DARM, which is evidently too little;
  • one hypothesis is that DARM may change sign due to some weird length/angular interaction, and that this messes up the actuation causing the lockloss;
  • one other possibility is that maybe, when arm power rises, there are some weird flashes that go back to the MC and then cause the locklosses, but this has to be verified;
  • attached there is a plot of the last lockloss (and a zoom of it), which seems to point at DARM as the culprit;





We left the IFO uncontrolled and in a "flashy" state so that tomorrow we can look into the "back-flashing to the MC" hypothesis.

  10855   Mon Jan 5 23:36:47 2015 ericqUpdateIOOAO cable reconnected


 I lost the connecting cable from the CM to the AO input (unlabeled). 

 This afternoon, I labelled both ends of this cable, and reconnected it to the MC servo board. 

  10854   Mon Jan 5 20:17:26 2015 jamieConfigurationCDSGDS upgraded to 2.16.14

I upgraded the GDS and ROOT installations in /ligo/apps/ubuntu12 the control room workstations:

  • GDS 2.16.14
  • ROOT 5.34.18 (dependency of GDS)

My cursory tests indicate that they seem to be working:


Now that the control room environment has become somewhat uniform at Ubuntu 12, I modified the /ligo/cdscfg/workstationrc.sh file to source the ubuntu12 configuration:

controls@nodus|apps > cat /ligo/cdscfg/workstationrc.sh
source /ligo/apps/ligoapps-user-env.sh
source /ligo/apps/ubuntu12/ligoapps-user-env.sh
source /opt/rtcds/rtcds-user-env.sh
controls@nodus|apps > 

This should make all the newer versions available everywhere on login.

  10853   Mon Jan 5 18:15:18 2015 JenneUpdateCDSiscex reboot

Rana noted last week that TRX's value was stuck, not getting to the lsc from iscex.  I tried restarting the individual models scx, lsc and even scy (since scy had an extra red rfm light), to no avail.  I then did sudo shutdown -r now on iscex, and when it came back, the problem was gone.  Also, I then did a diag reset which cleared all of the unusual red rfm lights.

Things seem fine now, ready to lock all the things.

  10852   Mon Jan 5 12:42:09 2015 ericqUpdateSUSBS misbehaving

The BS was showing some excess motion. I think I've fixed it. Order of operations:

  • The DC PIT bias from previous ASS runs was at ~500, I zeroed this and aligned the BS to be centered on its oplev QPD with DC alignment sliders
  • I squished the gold box cables. This changed the alignment slightly, and brought the UR voltage back to a normal value. Excess motion still existed
  • I found that the the C1:SUS-BS_LRSEN filter had HOLD OUTPUT enabled. I turned it off. All seems well. 

I'm not sure how this might have gotten switched on...

  10851   Sun Jan 4 22:08:46 2015 ranaUpdateIOOMC loop characterizations: PZT/EOM crossover

 * PMC + MC were unlocked when I came in.

* I fiddled around some more with the mcup/down scripts to make locking snappier. The locking was breaking the PMC lock often, so I re-enabled the MC servo board output limiter during acquisition. It is disabled in the MC UP script.

* Re-measured the MC OLG. Still OK.

* Measured the PZT / EOM crossover (aka the FAST / PC crossover) using the connectors on Koji's summing box. With the FAST gain at 18 dB, the crossover is ~10 kHz. Looks way to shallow. Plots to follow.

* I finally discovered today that the PMC PZT stroke is what's causing the main mis-alignment of the beam going to the IMC. By relocking at a few positions, I could see that the IOO QPDs have steps when the PMC relocks. So the IO beam wander is NOT due to temperature effects on the optics mounts of the PSL table. I wonder if we have a large amount of length to angle coupling or if this is the same as the OMC PZTs ?

P.S. I found that someone is using a temporary bench power supply to power the summing box between the TTFSS and the Thorlabs HV driver...whoever did this has ~48 hours to hook up the power in the right way or else Koji is going to find out and lose it and then you have to wear the Mickey Mouse hat.


The first attachment shows the OLG measurements with 2 different values of the fast gain (our nominal FG is 18 dB). You can see that the higher gains produce some crossover instability; when tuning the gain we notice this as an increase in the PCDRIVE rms channel.

The second attachment shows the measurement of the 'crossover'. Its really just the direct measurement of the IN1 / IN2 from the FAST summing box, so its the crossover measurement where the OLG is high.

Attachment 1: MC_OLGs.pdf
Attachment 2: MC_xover.pdf
  10850   Sun Jan 4 12:49:18 2015 SteveUpdateSUSrecent earthquakes

All suspensions were tripped. Damping were restored. No obvious sign of damage. BS OSEM-UR may be sticking ?

Attachment 1: recentEQ.png
  10849   Tue Dec 30 20:35:59 2014 ranaSummaryPSLPMC Tune Up
  1. Calibrated the Phase Adjust slider for the PMC RF Modulation; did this by putting the LO and RF Mod out on the TDS 3034 oscope and triggering on the LO. This scope has a differential phase measurement feature for periodic signals.
  2. Calibrated the RF Amp Adj slider for the PMC RF Modulation (on the phase shifter screen)
  3. The PMC 35.5 MHz Frequency reference card is now in our 40m DCC Tree.
  4.  The LO and RF signals both look fairly sinusoidal !
  5. Took photos of our Osc board - they are on the DCC page. Our board is D980353-B-C, but there are no such modern version in any DCC.
  6. The PMC board's Mixer Out shows a few mV of RF at multiples of the 35.5 MHz mod freq. This comes in via the LO, and can't be gotten rid of by using a BALUN or BP filters.
  7. In installed the LARK 35.5 MHz BP filter that Valera sent us awhile ago (Steve has the datasheet to scan and upload to this entry). It is narrow and has a 2 dB insertion loss.

For tuning the phase and amplitude of the mod. drive:

- since we don't have access to both RF phases, I just maximized the gain using the RF phase slider. First, I flipped the sign using the 'phase flip' button so that we would be near the linear range of the slider. Then I put the servo close to oscillation and adjusted the phase to maximize the height of the ~13 kHz body mode. For the amplitude, I just cranked the modulation depth until it started to show up as a reduction in the transmission by ~0.2%, then reduced it by a factor of ~3. That makes it ~5x larger than before.

Attachment 1: 17.png
Attachment 2: PMCcal.ipynb.xz
Attachment 3: PMC_Osc_Cal.pdf
  10848   Tue Dec 30 17:26:23 2014 ranaUpdatePSLRelaxation Osc and the NPRO Noise eater

I wonder if the variable bump around 100 kHz can be something about the NPRO and if the bump we see is the closed loop response due to the Noise Eater.


This plot (from the Mephisto manual) shows the effect of the NE on the RIN, but not the frequency noise. I assume its similar since the laser frequency noise above 10 kHz probably just comes from the pump diode noise.

I went out to the PSL and turned off the NE at ~4:53 PM local time today to see what happened. Although the overall PCDRIVE signal looks more ratty, there is no difference in the spectra of ON/OFF when the PCDRIVE is low. When its noisy, I see a tiny peak around 1 MHz with NE OFF. Turned it back on after a few hours.

  10847   Tue Dec 30 00:46:05 2014 ranaUpdateIOOInvestigations into the mad PCDRIVE

Koji and I noticed that there was a comb* of peaks in the MC and FSS at harmonics of ~37 kHz. Today I saw that this shows up (at a much reduced level) even when the input to the MC board is disconnected.

It also shows up in the PMC. At nominal gains, there is just the 37 kHz peak. After tweaking up the phase shifter settings, I was able to get PMC servo to oscillate; it then makes a comb, but the actual oscillation fundamental is 1/3 of 37 kHz (some info on Jenne from elog 978 back in 2008).

Not sure what, if anything, we do about this. It is curious that the peak shows up in the MC with a different harmonic ratio than in the PMC. Any theories?


Anyway, after some screwing around with phase and amplitude of the RF modulation for the PMC from the phase shifter screen**, I think the gain is higher in the loop and it looks like the comb is gone from the MC spectrum.

Another clue I notice is that the PCDRIVE mad times often are coincident with DC shifts in the SLOWDC. Does this mean that its a flakiness with the laser? While watching the PCDRIVE output from the TTFSS interface board on a scope, I also looked at MIXER mon. It looks like many of the high noise events are associated with a broadband noise increase from ~50-140 kHz, rather than some specific lines. Don't know if this is characteristic of all of the noisy times though.


* this 'comb' had several peaks, but seem not be precise harmonics of each other: (f3 - 3*f1)/f3 ~ 0.1%

** I think we never optimized this after changing the ERA-5 this summer, so we'd better do it next.

 *** UPDATE: the second plot show the comparison between the new quiet and noisy states. Its just a broad bump.


Attachment 1: MC_ERR.pdf
Attachment 2: plotFSSerr.ipynb.xz
Attachment 3: MC_ERRcomp.pdf
  10846   Mon Dec 29 21:30:25 2014 ranaUpdateGeneralrecovery
  1. Control room is at +66 F. Brrrr.
  2. Alignment of input beam into the IMC was wacky; locked on HOM.
  3. Re-aligned beam into the PMC first.
  4. Restarted mxstream for c1sus.
  5. Power cycled Martian router; all laptops were lost. Now better.
  6. Aligned launch beam from PSL to get onto the MCWFS better, MC is locking OK now. Moved MC SUS a little to get back to OSEM values from 6 days ago.
  7. Fixed LOCK_MC screen quad displays to be cooler.
  8. changed many of the ezcawrite calls in the mcup / mcdown to be 'caput -l' for more robustness. Still need ezcawrite for the binbary calls.
  9.  I didn't touch the mirrors on the MC REFL path, so we can still use that as a reference once the temperature returns to normal; the PSL room temp is down to 20C from 22 C a couple days ago.
  10. TRX values coming in to the LSC were frozen and the TRY_OUT16 was going to huge values even though camera flashes were reasonable. Tried restarting c1lsc model. No luck.
  11. Also tried shutdown -r now on c1lsc. No luck. Probably needs a RFM boot.
  12. Increased the FSS SLOW servo threshold to 9999 counts to avoid it running on some misaligned TEM01 mode locks. Increased the PID's I gain from 0.05 to 0.356 by tuning on some step responses as usual.
  13. By midnight the control room temperature is back around 71 F.
ELOG V3.1.3-