ID |
Date |
Author |
Type |
Category |
Subject |
Text |
 |
17064
|
Fri Aug 5 17:03:31 2022 |
Yehonathan | Summary | General | Testing 950nm laser found in trash pile | I set out to test the actuation bandwidth
of the 950nm laser. I hooked the laser to
the output of the bias tee of PD testing |
 |
17063
|
Fri Aug 5 12:42:12 2022 |
Koji | Update | IOO | IMC WFS: Overnight observation | The IMC lock survived overnight and the
WFS servo loops kept it aligned. The IMC
was unlocked in the morning. |
|
17062
|
Thu Aug 4 22:32:31 2022 |
Koji | Update | IOO | Upon leaving the lab (WFS investigation) | Upon leaving the lab:
- HEPA is ON at
the original speed (i.e. same speed at 5PM |
|
17061
|
Thu Aug 4 22:14:38 2022 |
Koji | Update | IOO | WFS investigation | WFS/MCTRANS_QPD Power Spectra
Attachment 1: HEPA ON
WFS1/2 PIT/YAW Spectra are stabilized |
 |
17060
|
Thu Aug 4 22:14:20 2022 |
Koji | Update | IOO | WFS investigation | Sensing matrix measurement
MCx_ASCyyy_EXC was shaken with
the amplitude of 3000 cnt. Measure the transfer |
   |
17059
|
Thu Aug 4 21:58:18 2022 |
Koji | Update | IOO | WFS investigation | OK... It seems that all the 6 dof of the
IMC WFS servo loops were closed with some
condition... |
   |
17058
|
Thu Aug 4 19:01:59 2022 |
Tega | Update | Computers | Front-end machine in supermicro boxes | Koji and JC looked around the lab today
and found some supermicro boxes which I was
told to look into to see if they have any |
   |
17057
|
Thu Aug 4 11:28:22 2022 |
Anchal | Update | PSL | FSSSlow/MCAutolocker issue (docker) | Added C1:IOO-MC_LOCK
to ALConfigMC.yml which solved the isse
with FSS Slow. We should tune the FSS Slow |
|
17056
|
Wed Aug 3 16:00:51 2022 |
yuta | Update | BHD | BHD fringe aligned with reduced LO and AS beam clipping | Last week, we could find an alignment which
realizes LO beam and AS beam both unclipped,
but it was not consistent with an alignment |
|
17055
|
Wed Aug 3 15:01:13 2022 |
Koji | Update | General | Borrowed Dsub cables | Borrowed DSUB cables for
Juan's SURF project |
|
17054
|
Tue Aug 2 17:25:18 2022 |
Tega | Configuration | BHD | c1sus2 dolphin IPC issue solved | [Yuta, Tega, Chris]
We did |
 |
17053
|
Tue Aug 2 01:10:26 2022 |
Koji | Update | IOO | WFS investigation | Continued to work on the WFS repair
Demod phase adjustment:
- Use the PDH signal to |
   |
17052
|
Mon Aug 1 18:42:39 2022 |
Tega | Configuration | BHD | c1sus2 IPC dolphin issue update | [Yuta, Tega]
We decided to give the dolphin
debugging another go. Firstly, we noticed |
  |
17051
|
Mon Aug 1 17:19:39 2022 |
Cici | Summary | General | RPitaya Data on Jupyter Notebook | Have successfully plotted data from the
Red Pitaya on Jupyter Notebook! Have
lost years of my life fighting with PyQt. |
|
17050
|
Sat Jul 30 12:48:18 2022 |
Koji | Update | PSL | FSSSlow/MCAutolocker issue (docker) | > it only starts working when C1:IOO-MC_LOCK
is 1 and C1:PSL-FSS_SLOWLOOP is 1.
- OK. Your new MCAutolocker does |
|
17049
|
Sat Jul 30 10:38:12 2022 |
Anchal | Update | PSL | FSSSlow/MCAutolocker issue (docker) | The FSSSlow script was not properly documented
and it was not working, so I had to use one
that I knew worked from CTN. This scripts |
|
17048
|
Fri Jul 29 22:37:54 2022 |
Koji | Update | IOO | WFS investigation | I wanted to check what's wrong with
the WFS.
I played with MC2 misalignment |
 |
17047
|
Fri Jul 29 20:21:11 2022 |
Koji | Update | PSL | FSSSlow/MCAutolocker issue (docker) | MCAutolocker/FSSSlow are not properly documented
and not properly working.
Tidy up the script and documentation, |
|
17046
|
Fri Jul 29 18:24:53 2022 |
Tega | Update | BHD | LO beam power improved by factor of 6 after LO and AS beam alignment | [Yuta, Tega]
From our previous work (elog 17044) |
   |
17045
|
Thu Jul 28 20:16:26 2022 |
Anchal | Update | BHD | Shaking test for LO beam AS beam to BHD DCPDs | Some insights from the inside vacuum situation:
The beam is an incident
near normal on PR2 close to the center of |
|
17044
|
Thu Jul 28 16:51:55 2022 |
Tega | Update | BHD | Shaking test for LO beam AS beam to BHD DCPDs | [Yuta, Tega, Yehonathan]
To investigate the BHD power imbalance
and clipping issues, we did some shaking |
 |
17043
|
Thu Jul 28 15:11:59 2022 |
Koji | Update | CDS | Too huge script_archive | As a result of the following work, the
file volume of /cvs/cds
was reduced from 3.2TB to 2.2TB, |
|
17042
|
Thu Jul 28 14:34:40 2022 |
Yehonathan | Update | BHD | LO beam power at BHD DCPDs is significantly lower than expected | {Yuta, Yehonathan}
We went to the BS table to check
the POP beam power. We first notice that |
|
17041
|
Thu Jul 28 13:09:28 2022 |
yehonathan | Update | BHD | Mode matching considerations | The LO beam was found to have a power of
60uW, 10% of the power expected. We are pretty
sure about the expectation because the AS |
|
17040
|
Wed Jul 27 18:30:50 2022 |
yuta | Update | BHD | LO beam power at BHD DCPDs is significantly lower than expected | [Paco, Yehonathan, Yuta]
We measured power and counts at
BHD DCPDs with LO beam only and ITM single |
 |
17039
|
Wed Jul 27 14:39:04 2022 |
Deeksha | Update | Electronics | New and improved PZT TF data from the DFD | Paco and I messed around with the attenuation
of the scope and bandwidth of the IF. We
also replaced the BNC T's in the |
  |
17038
|
Tue Jul 26 21:16:41 2022 |
Koji | Update | Computer Scripts / Programs | Vector fitting | I think the fit fails as the measurement
quality is not good enough.
|
|
17037
|
Tue Jul 26 20:54:08 2022 |
Paco | Update | BHD | BHD MICH test - LO phase control | [Yuta, Paco]
TL;DR
Successfully |
|
17036
|
Tue Jul 26 19:50:25 2022 |
Deeksha | Update | Computer Scripts / Programs | Vector fitting | Trying to vectfit to the data taken from
the DFD previously but failing horribly.
I will update this post as soon as I get |
 |
17035
|
Mon Jul 25 18:22:30 2022 |
Deeksha | Summary | Wiki | Measured the PZT TF Successfully | Measured the PZT beatnote using the setup
mentioned in elog post 17031. Attached is
the data taken from 10kHz to 1MHz, decadewise |
6x |
17034
|
Mon Jul 25 18:09:41 2022 |
Tega | Configuration | BHD | BHD Homodyne Phase control MEDM screen | [Paco, Tega, Yuta]
Today, we made a custom MEDM screen
for the BHD Homodyne Phase Control, which |
 |
17033
|
Mon Jul 25 17:58:10 2022 |
Tega | Configuration | BHD | c1sus2 IPC dolphin issue update | From the 40m
wiki, I was able to use the instructions
here |
   |
17031
|
Mon Jul 25 09:37:39 2022 |
Deeksha | Update | Electronics | Using the DFD to measure PZT TF | The DFD was setup to measure the change
in beatnote when excited. A long long (128in)
cable goes from the SR785 near the DFD all |
 |
17030
|
Mon Jul 25 09:05:50 2022 |
Paco | Summary | General | Testing 950nm laser found in trash pile | [Paco, Yehonathan]
==== Late elog from Friday ====
Koji provided us with a QFLD-950-3S |
 |
17029
|
Sun Jul 24 08:56:01 2022 |
Hang | Update | Calibration | Error propagation to astrophysical parameters from detector calibration uncertainty | Sorry I forgot to put tc & phic in
the example.
I modified astroFisherLib.py |
|
17028
|
Fri Jul 22 17:46:10 2022 |
yuta | Configuration | BHD | c1sus2 watchdog update and DCPD ERR channels | [Tega, Yuta]
We have added C1:HPC-DCPD_A_ERR and |
|
17027
|
Fri Jul 22 17:43:19 2022 |
Koji | Update | General | Obtained a functional CRT | [Koji Paco]
Koji went to Downs and found a
CRT labeled "for 40m Rana?". So |
|
17026
|
Fri Jul 22 15:05:26 2022 |
Tega | Configuration | BHD | c1sus2 shared memory and ADC fix | [Tega, Yuta]
We were able to fix the shared
memory issue by updating the receiver model |
   |
17025
|
Thu Jul 21 21:50:47 2022 |
Tega | Configuration | BHD | c1sus2 IPC update | IPC
issue still unresolved.
Updated shared memory tag so that |
|
17024
|
Wed Jul 20 18:07:52 2022 |
Paco | Update | BHD | BHD MICH test | [Paco, Yuta, JC]
We did some easy tests on the BHD
readout in preparation for BHD MICH. With |
|
17023
|
Wed Jul 20 15:58:52 2022 |
Koji | Summary | General | Jenne laser kaput! | For troubleshooting, the proper laser driver
(found beneath the AG network analyzer) was
connected. |
|
17022
|
Wed Jul 20 14:12:07 2022 |
Paco | Summary | General | Jenne laser kaput! | [Koji, Yehonathan, Paco]
Koji pointed out that this laser
was always driven with a current driver (which |
|
17021
|
Wed Jul 20 11:58:45 2022 |
Paco | Summary | General | Jenne laser kaput? | [Paco, Yehonathan, JC]
We were trying to setup the Jenne
laser to characterize the response of three |
|
17020
|
Tue Jul 19 18:41:42 2022 |
yuta | Update | BHD | Contrast measurements for Michelson and ITM-LO | [Paco, Yuta]
We measured contrast of Michelson |
|
17019
|
Tue Jul 19 17:18:34 2022 |
JC | Update | Electronics | New Coil Driver on Rack 1X3 | [Yehonathan, JC]
Yehonathan and I began to put the
electronics on Rack 1X3. To do this, we had |
|
17018
|
Tue Jul 19 16:00:34 2022 |
yuta | Configuration | BHD | Fast channels for BHD DCPDs now available in c1lsc but not in c1hpc | [Paco, Anchal-remote-support, Yuta]
We added fast channels to BHD DC
PDs. |
  |
17017
|
Tue Jul 19 07:34:46 2022 |
Anchal | Update | Calibration | Error propagation to astrophysical parameters from detector calibration uncertainty | Addressing the comments as numbered:
Yeah, that's correct,
that equation normally |
   |
17016
|
Mon Jul 18 21:41:42 2022 |
Anchal | Summary | LSC | FPMI locking procedure using REFL55 and AS55 | Now that you have found a working configuration,
I suggest we update CARM and DARM filter
banks so that they are used in locking those |
|
17015
|
Mon Jul 18 18:33:38 2022 |
Koji | Update | BHD | add Laser RIN to MICH budget | You should measure the coupling
by noise injection. Noise budgeting does
not need any modeling: |
|
17014
|
Mon Jul 18 17:07:12 2022 |
yuta | Update | LSC | x4.12 added to ETMX coil outputs to balance with ETMY | To balance the actuation on ETMX and ETMY,
x4.12
was aded to C1:SUS-ETMX_(UL|UR|LR|LL|SD)COIL |
|